By self developing the tacloid tooth in our Daido Hailong (Shanghai) Co. Ltd. in the Waigiao Free Trade Zone (100% share held by Daido Machinery Corporation), we made possible the combination of high superior performance and low cost.

■Features

Higher fluid displacement per tooth

Less vibration and noise during operation due to smooth combination of rotor and idler.

Operation per lower electricity.

■Specifications

・	Connection	NPT/BSP/ANSI/DIN

・	Pressure	1.38MPaG(200PSIG)

・	Temperature	149°C（300Ｆ）

・	Viscosity	75,000 CPS

・	Flow	757 L/min(200GPM)

■Legend


▼MATERIAL CODES

PUMP SIZE
2F =	25mm(1") Threaded Inlet/Discharge
4H =	38mm(1-1/2") Threaded Inlet/Discharge
4HL =	38mm(1-1/2") Threaded Inlet/Discharge
8AK =	51mm(2") Threaded Inlet/Discharge
8AL =	51mm(2") Threaded Inlet/Discharge
8K =	51mm(2") Threaded Inlet/Discharge
8KK =	51mm(2") Threaded Inlet/Discharge
8L =	51mm(2") Threaded Inlet/Discharge
12LQ =	64mm(2-1/2") Flanged Inlet/Discharge
15LL =	76mm(3") Flanged Inlet/Discharge
Note: No speciality code indicates NPT or ANSI

CASING/HEAD/BRACKET MATERIAL
G = Gray Iron

ROTOR
B	Bronze (available in TG4H
	TG4HL, TG8K, TG8KK, TG8L,
	TG12LQ and TG15LL models)
W	Ductile Iron (available in
	TG4H, TG4HL, TG8AK, TG8KK
	and TG8AL models)
M	Strrl (available in TG2F, TG4H
	TG4HL, TG8K, TG8KK, TG8L,
	TG12LQ and TG15LL models)
G	Gray Iron (available in TG2F
	TG8K, TG8L, TG12LQ and
	TG15LL models

IDLER
B =	Bronze (available in TG4H,
	TG4HL, TG8K, TG8KK, TG8L,
	TG12LQ and Tg15LL models)
W =	Ductile Iron (only available in?
	TG8AK and TG8AL models)
G =	Gray Iron (available in TG2F,
	TG4H, TG4HL, TG8K, TG8KK,
	TG8L, TG12LQ and TG15LL
	models

ROTOR SHAFT & IDLER PIN
M =	Steel

SEAL TYPE
125 =	Packed
4125 =	Mechanical Seal

BUSHING MATERIALS
B =	Bronze
C =	Carbon Graphite
	(not available for packed pumps)
S =	Siliconized Graphite2
	(not available for packed pumps)

SEAL MATREIALS
T =	PTFE Impregnated (packed only)
BC =	NBR/SiC ×　Carbon 2
	(Seal Ring x Mating Ring)
VC =	VitonR w/SiC　×　Carbon
	(Seal Ring x Mating Ring)
BS =	NBR/SiC　×　SiC 2
	(Seal Ring x Mating Ring)
VS =	ViltonR w/SiC　×　SiC 2
	(Seal Ring x Mating Ring)

INTERNAL PESSURE RELIEF VALVE
	For TG2F,TG4H andTG4HL
G1 =	Gray Iron 〔1.7-3.0bar(25-44psig)〕2
G2 =	Gray Iron 〔3.1-4.5bar(45-65psig)〕2
G3 =	Gray Iron 〔4.6-8.0bar(66-116psig)〕2
G4 =	Gray Iron 〔8.1-13.8bar(117-200psig)〕2

	For TG8AK,TG8AL,TG8L,TG12LQ andTG15LL
G1 =	Gray Iron 〔1.4-3.0bar(20-44psig)〕2
G2 =	Gray Iron 〔3.1-4.5bar(45-65psig)〕2
G3 =	Gray Iron 〔4.6-8.5bar(66-123psig)〕2
G4 =	Gray Iron 〔8.6-13.8bar(124-200psig)〕2

	For TG8K and TG8KK
G1 =	Gray Iron 〔1.0-3.0bar(15-44psig)〕2
G2 =	Gray Iron 〔3.1-4.5bar(45-65psig)〕2
G3 =	Gray Iron 〔4.6-8.5bar(66-123psig)〕2
G4 =	Gray iron 〔8.6-13.8bar(124-200psig)〕2

	For all units
Z =	None2

SE-series

TG-Series
GEAR PUMP LEGEND
Performance Criteria
SPECIALITY CODES


■Pump Selection Performance Criteria

Model	Nominal Pump Rating			Burst Pressure		Steel-fitted unites above this velocity	Maximum recommended discharge pressure		Maximum recommended temperature
	Nominal Pump Rating			Burst Pressure			Maximum recommended discharge pressure		Packed		Mechanical Seal
	LPM	GPM	RPM	psig	bar		bar	psig	°C	°F	°C	°F
TG2G	30	8	1,800	400	27.6	7,500	13.8	200	149	300	100	212
TG4H	57	15	1,800	400	27.6	25,000	13.8	200	149	300	100	212
TG4HL	114	30	1,800	400	27.6	7,500	13.8	200	149	300	100	212
TG8AK	189	50	1,200	400	27.6	25,000	10.3	150	149	300	100	212
TG8AL	284	75	1,200	400	27.6	25,000	10.3	150	149	300	100	212
TG8K	284	75	780	400	27.6	7,500	13.8	200	149	300	100	212
TG8KK	379	100	780	400	27.6	25,000	13.8	200	149	300	100	212
TG8L	511	135	640	400	27.6	25,000	13.8	200	149	300	100	212
TG12LQ	511	135	640	400	27.6	25,000	13.8	200	149	300	100	212
TG15LL	530	140	520	400	27.6	7,500	13.8	200	149	300	100	212


■SPECIALITY CODES

0014 = BSPT Connections
0504 = DIN Flange Connections

1 This unit is NOT retrofittable to the Viking G125 and G4125 series models
2 Special order option. May require additional lead times.


	Copyright 2003 DAIDO MACHINERY CORPRATION. All rights reserved.